Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA User Manual download pdf

Step 1: (Carefully read all instructions before

installation) Removal of the exhaust system on this

vehicle requires cutting and deburring the pipe 3.50"

behind the Pipe/Weld junction at the outlet side of the

secondary catalytic converter (Fig.1). To accomplish

this you must remove the cross brace and Catalytic

Converter shield. After the pipe has been cut, remove

the system by disengaging the welded hangers from

the OEM rubber insulators. Do not damage the

rubber insulators, as they will be used to mount the

new system.

Step 2: Begin installation of the new system by

fastening the Inlet Pipe Assembly to the catalytic

converter extension using the supplied 2.25" clamp,

and by fitting the welded hanger into the OEM rubber

insulator. Leave all clamps and fasteners loose for

final adjustment of the complete system. Install the

remaining assemblies in a similiar fashion using the

supplied band clamps.

Step 3: With all components mounted loosely, adjust

the system for overall aesthetics and clearance of

frame & bodywork. (MAGNAFLOW recommends at

least 1/2" of clearance between the exhaust system

and any body panels to prevent heat-related body

damage or fire.)

Step 4: Once a final position has been chosen for the

new system, evenly tighten all fasteners from front to

rear. The supplied band clamps must be VERY tight

to properly align the pipes and prevent leaks

(Approximately 40ft-lbs.) U-bolt clamps should be

tightened to approximately 30-35ft-lbs. Inspect all

fasteners after 25-50 miles of operation and retighten

if necessary.

Mufflers, Converters,

Systems and Tips

INSTALLATION INSTRUCTIONS

15497

2010 Mazda 3 2.5L

Warning: When working on, under, or around

any vehicle exercise caution. Please allow the

vehicle's exhaust system to cool before removal,

as exhaust system temperatures may cause

severe burns. If working without a lift, always

consult vehicle manual for correct lifting

specifications. Always wear safety glasses and

ensure a safe work area. Serious injury or death

could occur if safety measures are not followed.

** Magnaflow Performance Exhaust recommends professional

installation on all their products

Magnaflow Performance Exhaust - 22961 Arroyo Vista Rancho Santa Margarita, CA 92688

Main #: 1-800-990-0905 Technical Support: 1-800-959-9226 ext 4500

05/25/11

Rev: 000

Over Axle Pipe

Assy

Sht 1 of 2

Muffler

Assy

Mid Pipe

Assy

[3] 2.50" Clamps

[3] 2.25" Clamp

Inlet Pipe

Assy

D/S Tailpipe

Assy

P/S Tailpipe

Assy

1 2

Summary of Contents

Page 1 - 2010 Mazda 3 2.5L

Step 1: (Carefully read all instructions before installation) Removal of the exhaust system on this vehicle requires cutting and deburring the pipe 3.

Page 2 - 2010 - Mazda 3 2.5L

Mufflers, Converters, Systems and TipsINSTALLATION INSTRUCTIONS154972010 - Mazda 3 2.5L** Magnaflow Performance Exhaust recommends professional insta

Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA User Manual

Browse online or download User Manual for For the car Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA. MagnaFlow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHAUST User Manual

Summary of Contents

More documents for For the car Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA

Comments to this Manuals

Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA User Manual

Browse online or download User Manual for For the car Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA. MagnaFlow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHAUST User Manual

Summary of Contents

More documents for For the car Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA

Comments to this Manuals

Related products and manuals for For the car Magnaflow MAZDA 3 Stainless Cat-Back System PERFORMANCE EXHA